Why Are There Spots on My Windows After Cleaning?
Written by Alex, Owner of OutWash
Published
You’ve paid a professional to clean your windows, so you expect them to look clean. If you find spots or streaks, it’s fair to be annoyed.
The marks usually come from one of three things: dirt that dripped onto the glass after it was cleaned, dirt that wasn’t fully washed or rinsed away, or minerals left behind by the water. Each one has a different fix, so the first job is working out which it is.
Is it normal for windows to be left wet?
Yes. If your cleaner uses a water-fed pole, you’ll see the windows left to dry on their own.
The pole uses specially filtered water, which has the minerals taken out of it. Ordinary tap water is full of tiny dissolved minerals, and they’re what leave a white mark when a drop dries. Filtered water doesn’t have them, so it can dry on the glass without leaving a mark.
So a wet window isn’t a problem. A mark that’s still there once the glass is fully dry is a different matter.
What causes spots and streaks after window cleaning?
Dirt dripping from frames and around vents
Frames collect dirt in the edges, the corners and around the little vents at the top of the window. When the water hits those places, it can pick up some of that dirt and carry it down onto the glass.
That’s why a window can look perfect when the cleaner leaves, then show a streak an hour later once the drips have dried.
The worst place I clean for this is a new build site in Exeter. Building work leaves a lot of dust and debris behind, and it settles in the vents and along the top of the frames. As soon as water touches it, it turns into dirty water, and there’s plenty of it waiting to run down onto the glass below. It’s about as bad as it gets for dirty drips, so every time I’m there I take extra care. I give the top of each frame more attention than I would on an older house, and I don’t clean the glass until the frames have stopped dripping.
Dirt or soap left on the glass
Washing the glass loosens the dirt, but the dirt then has to be rinsed away. If some is left behind, it dries as a mark. Old cleaning product from a previous clean can stick around too, and sometimes needs a bit of extra work to shift.
Water that still has minerals in it
As above, ordinary tap water leaves marks as it dries. If the water in the pole hasn’t been filtered properly, those minerals end up on your glass. That’s why checking the water is part of finding the cause when spots appear.
These are only the likely causes. A photo or a description doesn’t always tell you which one it is, so the cleaner may need to look at the window in person.
Can you tell if a window is going to spot?
Often, yes. I watch how the water behaves on the glass.
- A drop that runs down in a dead straight line. On properly clean glass, water tends to spread out and slide off in a sheet. When a drop picks one narrow path and runs straight down, it’s often because there’s something on the glass guiding it, or because it’s carrying dirt with it. Either way, when that line dries, it’s likely to leave a mark.
- Small, even dots of water in a single line. Water beads up like this when the glass or the edge it’s sitting on isn’t completely clean. A line of neat, matching dots usually means something is sitting along that edge, holding the water in place. As the dots dry, whatever was in or under them is left behind as spots.
I say “often” and “likely” because it isn’t certain. But it’s a good warning sign, and when I see it I go back and wash and rinse that area again before I move on.
Why can a first clean need extra attention?
If a window hasn’t been cleaned properly for a long time, there’s a lot of built-up dirt, especially in the frames. One wash and rinse may not be enough to shift it all.
That’s why a first clean often takes me two to three times as long as a regular clean. It takes several passes to get the frames and glass properly clean. My aim is clean windows the first time I leave, and if any marks show up afterwards, I want to find out why.
What should you do if spots remain?
It’s simple:
- Let the glass finish drying. Some marks are just damp patches and will disappear.
- Note which windows are affected. If the marks show up well, take a photo.
- Get in touch with your cleaner soon. Give them a chance to come back, have a look and put it right.
Please don’t feel awkward about asking. Any decent window cleaner would rather hear about a problem than have you quietly unhappy.
How I approach this at OutWash
- First cleans: I allow two to three times longer than for a regular clean, because that’s when the most dirt has built up.
- Frames first, then glass: I go all the way round the house and clean the frames first. Then I clean the glass, once the frames have had time to stop dripping. That way the dirty water has already run off before I clean the glass.
- Watching the water: While I work, I watch how the water runs down the glass. If I see warning signs, I deal with them before moving on.
- If something isn’t right: If you’re not fully happy, I’ll come back within 48 hours.
Want your windows cleaned regularly?
I clean windows every six weeks in Exeter and the surrounding areas. If you’d like to know how it works, have a look at my regular window cleaning page, or get in touch with any questions.
